OpenPilot Revolution Flight Controller

OpenPilot Revolution from the OpenPilot project introduces the generation of multi-purpose aircraft stabilization platforms.

Manufactured and purchased from the OpenPilot program!

The Revolution Flight Controller, this item also included is a 433Mhz MMCX Antenna and the Revolution RC Cable.

This version is 433Mhz and has a genuine Amphenol brand right angle MMCX connector.

There is a limit of ordering 2 Revos per customer currently.

For info:

Open Pilot Project Page
Open Pilot Forums
Getting Started
Running ArduPilot32 on REVO WIKI
Running ArduPilot32 on REVO Thread

Status
While the Revolution is currently a very capable flight controller, it is not yet a fully polished turnkey product. It is part of an Open Source community development effort and that is what really makes joining the Revolution exciting. There is a lot of interesting and challenging code left to write on the software side, there is also a lot of testing that needs to be performed, as well.
This community involvement is a big part of the OpenPilot project. We need you to get involved! (on the forum and the wiki). However, if you are an end user just looking to simply get in the air as fast as possible, the Revolution may not be for you at this time.

REVOLUTION HARDWARE MANUAL

Harga Rp. 2.100.000,-

OpenPilot Revolution from the OpenPilot project introduces the generation of multi-purpose aircraft stabilization platforms.

 

Manufactured and purchased from the OpenPilot program!

 

The Revolution Flight Controller, this item also included is a 433Mhz MMCX Antenna and the Revolution RC Cable.

 

This version is 433Mhz and has a genuine Amphenol brand right angle MMCX connector.

 

There is a limit of ordering 2 Revos per customer currently.

 

For info:

 

Open Pilot Project Page

Open Pilot Forums

Getting Started

Running ArduPilot32 on REVO WIKI

Running ArduPilot32 on REVO Thread

 

Status

While the Revolution is currently a very capable flight controller, it is not yet a fully polished turnkey product. It is part of an Open Source community development effort and that is what really makes joining the Revolution exciting. There is a lot of interesting and challenging code left to write on the software side, there is also a lot of testing that needs to be performed, as well.

This community involvement is a big part of the OpenPilot project. We need you to get involved! (on the forum and the wiki). However, if you are an end user just looking to simply get in the air as fast as possible, the Revolution may not be for you at this time.

 

REVOLUTION HARDWARE MANUAL

- See more at: http://kamkits.com/index.php?route=product/product&product_id=381#sthash.5rfece64.dpuf

OpenPilot Revolution from the OpenPilot project introduces the generation of multi-purpose aircraft stabilization platforms.

 

Manufactured and purchased from the OpenPilot program!

 

The Revolution Flight Controller, this item also included is a 433Mhz MMCX Antenna and the Revolution RC Cable.

 

This version is 433Mhz and has a genuine Amphenol brand right angle MMCX connector.

 

There is a limit of ordering 2 Revos per customer currently.

 

For info:

 

Open Pilot Project Page

Open Pilot Forums

Getting Started

Running ArduPilot32 on REVO WIKI

Running ArduPilot32 on REVO Thread

 

Status

While the Revolution is currently a very capable flight controller, it is not yet a fully polished turnkey product. It is part of an Open Source community development effort and that is what really makes joining the Revolution exciting. There is a lot of interesting and challenging code left to write on the software side, there is also a lot of testing that needs to be performed, as well.

This community involvement is a big part of the OpenPilot project. We need you to get involved! (on the forum and the wiki). However, if you are an end user just looking to simply get in the air as fast as possible, the Revolution may not be for you at this time.

 

REVOLUTION HARDWARE MANUAL

- See more at: http://kamkits.com/index.php?route=product/product&product_id=381#sthash.5rfece64.dpuf

OpenPilot Revolution from the OpenPilot project introduces the generation of multi-purpose aircraft stabilization platforms.

 

Manufactured and purchased from the OpenPilot program!

 

The Revolution Flight Controller, this item also included is a 433Mhz MMCX Antenna and the Revolution RC Cable.

 

This version is 433Mhz and has a genuine Amphenol brand right angle MMCX connector.

 

There is a limit of ordering 2 Revos per customer currently.

 

For info:

 

Open Pilot Project Page

Open Pilot Forums

Getting Started

Running ArduPilot32 on REVO WIKI

Running ArduPilot32 on REVO Thread

 

Status

While the Revolution is currently a very capable flight controller, it is not yet a fully polished turnkey product. It is part of an Open Source community development effort and that is what really makes joining the Revolution exciting. There is a lot of interesting and challenging code left to write on the software side, there is also a lot of testing that needs to be performed, as well.

This community involvement is a big part of the OpenPilot project. We need you to get involved! (on the forum and the wiki). However, if you are an end user just looking to simply get in the air as fast as possible, the Revolution may not be for you at this time.

 

REVOLUTION HARDWARE MANUAL

- See more at: http://kamkits.com/index.php?route=product/product&product_id=381#sthash.5rfece64.dpuf

OpenPilot Revolution from the OpenPilot project introduces the generation of multi-purpose aircraft stabilization platforms.

 

Manufactured and purchased from the OpenPilot program!

 

The Revolution Flight Controller, this item also included is a 433Mhz MMCX Antenna and the Revolution RC Cable.

 

This version is 433Mhz and has a genuine Amphenol brand right angle MMCX connector.

 

There is a limit of ordering 2 Revos per customer currently.

 

For info:

 

Open Pilot Project Page

Open Pilot Forums

Getting Started

Running ArduPilot32 on REVO WIKI

Running ArduPilot32 on REVO Thread

 

Status

While the Revolution is currently a very capable flight controller, it is not yet a fully polished turnkey product. It is part of an Open Source community development effort and that is what really makes joining the Revolution exciting. There is a lot of interesting and challenging code left to write on the software side, there is also a lot of testing that needs to be performed, as well.

This community involvement is a big part of the OpenPilot project. We need you to get involved! (on the forum and the wiki). However, if you are an end user just looking to simply get in the air as fast as possible, the Revolution may not be for you at this time.

 

REVOLUTION HARDWARE MANUAL

- See more at: http://kamkits.com/index.php?route=product/product&product_id=381#sthash.5rfece64.dpuf

Rctimer Multifunction Gimbal Controller for All Gim

 

Rctimer Multifunction Gimbal Controller for All Gimbals

Including 4 pins cable total 700mm length


Harga Rp. 110.000,-

Rctimer Multifunction Gimbal Controller for All Gimbals

 

Including 4 pins cable total 700mm length

 

- See more at: http://kamkits.com/index.php?route=product/product&product_id=436#prettyPhoto

DJI NAZA-M V2 + GPS Combo

WHAT’S NEW WITH THE NAZAM V2 : FIRMWARE AND FUNCTIONS

New attitude stabilization algorithm, provides better flight performance / maneuverability;
New flight control performance, provides better flight experience; (flight control is smoother, take‐off iseasier)
Support for Octo‐rotor;
One‐motor stopped still can land safely (Hexa‐rotor, Octo‐rotor)
Automatic course deviation compensation, reduced the effects of magnetic disturbance; interference around the compass detection & warning;
Added IMU advanced calibration, error identification and warning, reduced the impact of sensor error to the flight performance

ADVANCED & IMPROVED ATTITUDE STABILIZATION ALGORITHM

The latest fourth generation attitude stabilization algorithm not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability. It is more flexible and stable, and gives the hobbyists a wonderful flight experience. New features have been included such GPS course automatic compensation, GPS & Compass sensor calibration, new take-off mode and so on.

NINE TYPES OF MULTI-ROTORS SUPPORTED

Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
Quad I, Quad X;
Hexa I, Hexa V, Hexa Y, Hexa IY;
Octo X, Octo I, Octo V; ( Naza-M V2 does not support the aircraft which has large vibration, so when you choose to use hexa-rotor or octo-rotor, please pay attention to the vibration situation and try to do some vibration dampening)

MULTIPLE FLIGHT CONTROL MODES/INTELLIGENT SWITCHING
It offers three types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode, Manual Mode. Customer can switch among the three modes to adjust different flight environment. It also can adjust automatically in the flight environment and intelligent switch between GPS Atti. Mode and Atti. Mode to make sure the safety and security of flight. In the software at the position of the manual mode you can choose manual, attitude or failsafe; it supports one key failsafe trigger.


Harga Rp. 4.200.000,-

AlexMos 3-Axis 3.0 Version Brushless Gimbal Controller

AlexMos 3 axis Sipmle BGC w / 2.3 Firmware

We have contacted to Alex about the V3.0 manual, and we will update the manual ASAP.

Warning!!!
Please in strict accordance with the above connection mode properly connected gyro and extended board, Pay attention to the connection error may cause permanent damage of the board.

Please read this befor your purchase:
We have tested our inventory, we receive all Alexmos Controllers direct from Alex, it is common for individuals to incorrectly apply power and damage these sensitive boards.
We will warranty Only manufacturer defects and will not support boards damaged by purchaser. If you feel your board is Maufacture defect. Return at your expense and we will evaluate. If we discover a manufacture defect, we will replace and ship a replacement at no charge


Product Description

AlexMos SimpleBGC V3.0 "AlexMos"  Simple Brushless Gimbal Controller. This board set is fully assembled and ready to use board with latest firmware designed by Alex Moskalenko.
What's NEW:
- New option: skip gyro calibraion at startup. With this option checked, board starts working immediately after power ON.
- New menu command and GUI button for manual gyro calibration RC Map, RC Source moved to profiles. It allows to change RC control setting by switching profiles.
- RC YAW axis control may be  inverted now by specifying Min.angle > Max.angle, like for other axis (but this setting not used for limiting, just for inverting).
- I2C errors monitoring: LED will blink when I2C error detected
- New option: gyro high sensivity. It doubles sensivity of the gyro, that  equals to multiplying gains in the PID controller by 2.  It may be usefull for big DSLR cameras.
- The "Firmware Upgrade" tab in the GUI is working now and allows to upload a new firmware.

Specifications:
50*50mm size with 45*45mm mounting hole pattern for M3 screws
Onboard mini-USB
Access to serial port, so a Bluetooth can also be hooked for easy tuning.
L6234 Motor drivers
Atmega 328P with Alexmos Bootloader preinstalled
Controller weight: 15 grams
MPU6050 IMU included
Downloads
Firmware: SimpleBGC_2_1.enc.hex
GUI: SimpleBGC_GUI_2_1.zip
Driver:Cp2102 USB Driver


Harga Rp. 2.200.000,-

AlexMos 3 axis Sipmle BGC w / 2.3 Firmware

 

We have contacted to Alex about the V3.0 manual, and we will update the manual ASAP.

 

Warning!!!

Please in strict accordance with the above connection mode properly connected gyro and extended board, Pay attention to the connection error may cause permanent damage of the board.

 

Please read this befor your purchase:

We have tested our inventory, we receive all Alexmos Controllers direct from Alex, it is common for individuals to incorrectly apply power and damage these sensitive boards.

We will warranty Only manufacturer defects and will not support boards damaged by purchaser. If you feel your board is Maufacture defect. Return at your expense and we will evaluate. If we discover a manufacture defect, we will replace and ship a replacement at no charge

 

 

 

Product Description

 

AlexMos SimpleBGC V3.0 "AlexMos"  Simple Brushless Gimbal Controller. This board set is fully assembled and ready to use board with latest firmware designed by Alex Moskalenko.

What's NEW:

- New option: skip gyro calibraion at startup. With this option checked, board starts working immediately after power ON.  

- New menu command and GUI button for manual gyro calibration RC Map, RC Source moved to profiles. It allows to change RC control setting by switching profiles.

- RC YAW axis control may be  inverted now by specifying Min.angle > Max.angle, like for other axis (but this setting not used for limiting, just for inverting).

- I2C errors monitoring: LED will blink when I2C error detected

- New option: gyro high sensivity. It doubles sensivity of the gyro, that  equals to multiplying gains in the PID controller by 2.  It may be usefull for big DSLR cameras.

- The "Firmware Upgrade" tab in the GUI is working now and allows to upload a new firmware.

 

Specifications:

50*50mm size with 45*45mm mounting hole pattern for M3 screws

Onboard mini-USB

Access to serial port, so a Bluetooth can also be hooked for easy tuning.

L6234 Motor drivers

Atmega 328P with Alexmos Bootloader preinstalled

Controller weight: 15 grams

MPU6050 IMU included

Downloads

Firmware: SimpleBGC_2_1.enc.hex

GUI: SimpleBGC_GUI_2_1.zip

Driver:Cp2102 USB Driver

 

 

 

 

- See more at: http://kamkits.com/index.php?route=product/product&product_id=399#prettyPhoto

AlexMos 3 axis Sipmle BGC w / 2.3 Firmware

 

We have contacted to Alex about the V3.0 manual, and we will update the manual ASAP.

 

Warning!!!

Please in strict accordance with the above connection mode properly connected gyro and extended board, Pay attention to the connection error may cause permanent damage of the board.

 

Please read this befor your purchase:

We have tested our inventory, we receive all Alexmos Controllers direct from Alex, it is common for individuals to incorrectly apply power and damage these sensitive boards.

We will warranty Only manufacturer defects and will not support boards damaged by purchaser. If you feel your board is Maufacture defect. Return at your expense and we will evaluate. If we discover a manufacture defect, we will replace and ship a replacement at no charge

 

 

 

Product Description

 

AlexMos SimpleBGC V3.0 "AlexMos"  Simple Brushless Gimbal Controller. This board set is fully assembled and ready to use board with latest firmware designed by Alex Moskalenko.

What's NEW:

- New option: skip gyro calibraion at startup. With this option checked, board starts working immediately after power ON.  

- New menu command and GUI button for manual gyro calibration RC Map, RC Source moved to profiles. It allows to change RC control setting by switching profiles.

- RC YAW axis control may be  inverted now by specifying Min.angle > Max.angle, like for other axis (but this setting not used for limiting, just for inverting).

- I2C errors monitoring: LED will blink when I2C error detected

- New option: gyro high sensivity. It doubles sensivity of the gyro, that  equals to multiplying gains in the PID controller by 2.  It may be usefull for big DSLR cameras.

- The "Firmware Upgrade" tab in the GUI is working now and allows to upload a new firmware.

 

Specifications:

50*50mm size with 45*45mm mounting hole pattern for M3 screws

Onboard mini-USB

Access to serial port, so a Bluetooth can also be hooked for easy tuning.

L6234 Motor drivers

Atmega 328P with Alexmos Bootloader preinstalled

Controller weight: 15 grams

MPU6050 IMU included

Downloads

Firmware: SimpleBGC_2_1.enc.hex

GUI: SimpleBGC_GUI_2_1.zip

Driver:Cp2102 USB Driver

 

 

 

 

- See more at: http://kamkits.com/index.php?route=product/product&product_id=399#prettyPhoto

DJI H3-2D Phantom GoPro3+ Zenmuse 2 Axis Gimbal

DJI GOPRO ZENMUSE GIMBAL FOR P330 PHANTOM ---> UPGRADE BRACKET ALUMINIUM

TECHNICAL SPECIFICATIONS OF DJI ZENMUSE HD-2D GIMBAL:

    Weight (Gopro Hero 3 included): 230g
    Input Voltage: 12V~16.8V
    Working Current: static current 400mA (@12V) / Dynamic current 600mA (@12V)
    Operating Temperature: -10°C~50°C
    Dimensions (damping kit included)：99.5mm*85.5mm*92.75mm
    Controlled Angle Accuracy: +/- 0.08°
    Working Angle Limit: Pitch 50°~ -130° Roll ±39°
    Supported camera: GoPro Hero 3


FEATURES OF DJI GOPRO PHANTOM GIMBAL

    Plug and Play No additional manual adjustment needed, do not need to adjust the C.G. or parameters in the software, easy mounting.
    Compatible with DJI flight control systems
    The H3-2D gimbal is compatible with DJI flight control systems, it can adjust the roll and pitch angle according to the accurate control of the Gimbal feedback and communicate with the MC in real-time.
    It supports WooKong-M, NAZA-M V1, NAZA-M V2, Phantom;
    It will support Ace One, WooKong-H, NAZA-H;
    It doesn't support NAZA-M LITE.
    Notice: NAZA-M V1 and Phantom users need the PMU of NAZA-M V2.
    Ideal stabilizer for Phantom The mechanical design, weight will match the Phantom perfectly, the Phantom transmi - tter could be easily upgrade to the function of gimbal controlloing with a customized adjuster, no additional receiver channels needed just re-using the X1 channel.
    Inherited the core algorithm from Zenmuse Z15 gimbal and the unmanned aircraft flying attitude stability control algorithm, combined with high precision sensor, DJI Zenmuse H3-2D gimbal provides pixel level stabilized footage.
    Independent IMU module provides precise attitude data and closed-loop control improved control accuracy, no additional installation and connection needed, stable and reliable.
    Aluminum alloy material and innovative mechanical design makes the gimbal extreme light weight (230g total, GoPro Hero3 included). The aluminum frame structural design guarantees the strength of the gimbal.
    Online upgrade - The functions could be easily upgraded by online firmware upgrade.
    Customized for Gopro Hero3 - The gimbal is customized for Gopro Hero3, remote start/end shooting, video transmission (need video downlink) etc will be supported by future firmware upgrade.


Notice following points before you use it.

    Please kindly visit the following site for manual, notes, assistant software, firmware and driver of Zenmuse H3-2D Gimbal: http://www.dji-innovations.com/download/zenmuse-h3-2d-gimbal-downloads/
    Please kindly make sure the firmware of IMU, GCU and CMU of Zenmuse H3-2D Gimbal are upgraded to the latest version via the assistant software V1.02. (Latest firmware version：IMU V1.2, GCU V1.4, CMU V1.0)；
    Please kindly confirm the Gopro Hero3 camera is correctly connected to the Zenmuse H3-2D Gimbal before the Gimbal is powered on;
    Please kindly notice that no external force is allowed on Zenmuse H3-2D Gimbal during the process of self-checking and in normal use
Harga Rp. 4.600.000,-