OpenPilot CC3D 32Bits Flight Controller & Protect Case

OpenPilot CC3D 32Bits Flight Controller & Protect Case for Quadcopter QAV250 450

 

 

100% Brand New

 

The CC3D board is an all-in-one stabilization hardware which runs the OpenPilot  firmware. It can fly any airframe from fixed wing to an octocopter and is  configured and monitored using the OpenPilot Ground Control Station (GCS)  software.

 

CopterControl from the OpenPilot project  introduces a new generation of multi-purpose aircraft stabilization platforms.  The CC3D has been designed from the ground up to perform the following functions:

- a MultiRotor controller with auto-level, including TriCopters, QuadCopters and  HexaCopters

- a Flybarless Helicopter controller with auto-level

 

 

The CopterControl hardware has the following features:

Powerful STM32 32-bit microcontroller running at 90MIPs with 128KB Flash and  20KB RAM

3-axis high-performance MEMs gyros and 3-axis high-performance MEMs  accelerometer

Tiny 36mmx36mm 4 layer PCB for superior electrical noise reduction and flight  performance.

Software support for Windows, Mac and Linux

Direct high speed USB support with no drivers required, a truly plug and play  device.

Spektrum satellite receiver support

Futaba S-BUS hardware support

Innovative Flexi-port technology for superior port flexibility

4Mbits on-board EEPROM for configuration storage

 

Manual:

//wiki.openpilot.org/display/Doc/CopterControl+Hardware+Manual

 

Setup Wizard: 

//wiki.openpilot.org/pages/viewpage.action?pageId=20250682

 

Package includes:

1 x CC3D OpenPilot FC

2 x 4pin cable

1 x 8pin cable

1 x Protect case

'
Harga Rp. 325.000,-

RS232/TTL JPEG Digital Serial CCTV Camera Module SCB-1

RS232/TTL JPEG Digital  Serial  CCTV Camera  Module SCB-1 with video out Support  VIMICRO VC0706 protocol 

Harga Rp. 325.000,-


 
Specification

• Video output:      CVBS 30fps
• PCB dimension:38×38mm/32×32mm
• Image sensor:1/4 CMOS image sensor MT9V011
• Image format: PAL, 628×582; NTSC, 510×492; default as NTSC for this module, PAL without resistor R5 (10K), free for users to choose
• Picture format: JPEG
• Image size: VGA / QVGA / QQVGA CIF / QCIF / QQCIF, generally default as QVGA (320*240), users are free to change the size according to the communication protocol. The smaller the picture, the faster the picture is sent.
• Baud rate: 9600bps-115200bps, default as 38400, users are free to change the rate according to the communication protocol.
• Lens: FOV 60°~120°, 650 ordinary lens / 850, 940 IR lens
• Terminal blocks: 6PIN-2.0mm/2PIN-2.0mm (Infrared light board interface)
• Level: Default as CMOS level, can be modified to TTL level in accordance with the requirements
• Working voltage: DC4.8V ~ DC6.5V
• Working current: 90mA (when infrared light does not work)
• Working temperature: -20C~ +60C
• Storage temperature: -30C~ 70C
• Humidity: 90% non-condensing

Software debugging tool image acquisition process / Command image acquisition process
1. Software tool image acquisition process
First step:
 Connect to 5V power supply, then connect the module with computer via serial cable. Please note that the serial port of debugging tool must be the same as the serial port of COM in computer device manager.
If there is no RS232 interface in the laptop , please download a conversion tool to convert USB interface into RS232 interface (this is unstable, not recommended). Please note that the serial port of debugging tool must be the same as the serial port of COM in computer device manager.
Second step:
Open the debugging tool:
Choose correct ‘COM Port BeatRate'(original default as 38400), others remain unchanged, then click ‘Open'.
Click ‘Get Version'"f it indicates ‘successful connection' in the right, connection succeeds. If it indicates ‘CMD time', connection fails, please check.
Third step:
Collect images and send them to display on the computer via serial port ;
Click ‘Fbuf Ctrl',a new interface will turn up, then click ‘Stop Fbuf',click ‘Sel File' to save the file, finally click ‘Read' button to read the images.
2. Command image acquisition process: 
The following is a continuous operation of photo taking and data uploading for reference only.
Step 1:Send 56 00 36 01 00  to stop current frame 
Step 2:Send 56 00 34 01 00   to obtain the data length of current frame
Receive returned data:76 00 34 00 04FF FF FF FF(red indicates bytes of BUFF, 4 bytes)
Step 3:Send:56 00 32 0C 00 0A00 00 00 00FF FF FF FF10 00(blue indicates that the data is with fixed value)
Returned data from the serial port:76 00 32 00 00FF D8 ...Image data... FF D976 00 32 00 00
Step 4:Send :56 00 36 01 03  to recover frame, back to normal working status 
Common control commands (for details, please refer to the communication protocol) - Communication guideline
1. Reset command:56 00 26 00  Return:76 00 26 00
2. Photo taking command:56 00 36 01 00 Return:76 00 36 00 00
3. Reading the length of photo taken command:56 00 34 01 00 Return:76 00 34 00 04 00 00 XX YY
 XX YY -------Image data length,XX is high byte while YY is low byte
4. Reading data of the photo taken command:56 00 32 0C 00 0A 00 00 XX XX 00 00 YY YY ZZ ZZ
Return:76 00 32 00 00(interval)FF D8.......FF D9(interval)76 00 32 00 00
00 00 XX XX ------starting address (starting address must be multiples of 8, generally set as 00 00)
00 00 YY YY ------image data length(high byte first and then low byte)
ZZ ZZ       --------interval(= XX XX*0.01ms,better to set it less, such as 00 0A)
Note:JPEG image file must begin with FF D8 and end up with FF D9
5. Stop photo taking command:56 00 36 01 03  Return:76 00 36 00 00
6. Set photo compression ratio command:56 00 31 05 01 01 12 04 XX  Return:76 00 31 00 00
XX is generally selected as 36  (range: 00 ----FF)
7. Set photo size command:
56 00 31 05 04 01 00 19 11 (320*240)Return:76 00 31 00 00
56 00 31 05 04 01 00 19 00 (640*480)
8. Modify serial speed:56 00 24 03 01 XX XX    Return:76 00 24 00 00
XX XX        Speed
AE C8         9600
56  E4        19200
2A F2         38400
 

Take photo Steps(PC)
First Step: Connect

1.  Connect SCA/SCB Camera module To PC Serial port 

       2   Connect to DC 5V
Second Step:  Open tools

1.  OPEN“VC0706CommTool”Software

 

Third Step: Set Serial Port
1. Set and Open Serial port
A:Step:Select  COM port  [ Default COM1,Please check ];
B::Select Baud Rate :[ Select the same baud rate with camera module.[
C: Click Open button,Open serial port.
2  Testing Serial Port
A  Select “Get Version”and Click


Fourth step:Take photo

1. Select “Fbuf Ctrl” and Click
2. Select “Stop Cfbuf “and Click,Take photo
3. Select “Sel File” and Save files
4. Select “Read” button,Success!

Notice:  Take photo again, please click  “Resume” Button,  Reset the camera module
 and then operate 1 2 3 4 steps

Arduino UNO ATMEGA 328 DIP

Arduino ATMEGA 328 DIP + kabel

Harga Rp 150.000,-

ESC 30A SimonK Prgramme RC Brushless

Product Description

 

Highest efficiency 100% N-FET design.

Highest accuracy with Crystal Oscillator (Temperature won't affect the PWM operating range like other cheap ESC's).

No low voltage cutoff, because any cutoff in a multirotor = crash.

No over temp cutoff, because any cutoff in a multirotor = crash.

Super high refresh rate, no buffering of the input signal, resulting in more than 490Hz response rate.

16KHz motor frequency, giving fastest response of the motor, and quietest operation as well (no 8KHz squeal).

Super simple, foolproof operation! Nothing to program other than the throttle range.

Don't buy a 30A multirotor ESC that doesn't meet all these criteria! There are a lot of low quality 30A ESC out there!

ESC Specification
Cont Current: 30A
Burst Current: 35A
BEC Model: Linear mode
BEC Output: 5V3A
Li-ion/Li0poly:2-4S,or Ni-MH/Ni-Cd:4-12NIMH
Weight: 25g
Size: 32*24*7mm

Harga Rp. 150.000,-

JST 2 pin connector plug lead wire

 

Features:
100mm helicopter lipo Battery plug JST connector
Can be used on most mini RC helicopter and indoor 3D plane
Great for small Lipo and NiMh connection

Specification:
Original box: NO
Length:100mm 10cm (approximate 4")
Net weight: 5g
Color: Red & Black



Harga Rp. 7.000,-/pasang

Universal Tall Landing gear skids DJI F450 F550 SK480 FPV aerial photo

Product Description:

 

4pcs universal Tall Landing gear skids for DJI F450 F550 SK480 FPV aerial photo

Height:150mm

weight:90 grams

easy for install on the DJI F450 F550 or similar frame

come with 4pcs for one full set.

come with M2.5*8 Screws for assembling

Harga Rp. 150.000,-

Propeller 5030

5030 EP Direct Drive 5x3 5*3 Propellers Prop

These propellers are designed for park fly applications with direct drive brushless motors.

The picture below shows all the propellers included in the same category, The description tells what is included in this auction

Item specifics

Use:Vehicles & Remote Control Toys

Technical parameters:Value 3

For Vehicle Type:Airplanes

Brand Name:Gemfan

Tool Supplies:Grinded

Material:Plastic

Upgrade Parts/Accessories:Wheel Hub

Model Number:5030

Four-wheel Drive Attributes:Battery

Color:orange/green/black

use:quadcopter

Harga Rp. 23.000 /pasang

Ubec 3-5 A

Product name:

Hobbywing 5V 6V 3A Switch-Mode  BEC UBEC 

Output: 5V/3A and 6V/3A switchable

Ripple: <50mVp-p(@2A/12V)

Input: 5.5V-26V (2-6 cells Lipo battery pack or 5-18 cells NiMH battery pack)

Size: 41.6mm*16.6mm*7mm (L*W*H)

Weight: 11g

Features:

• The UBEC is an advanced switching regulator with over-current and over-heat protection function,and the maximun efficiency of the system is nearly 90%.
• The small size and the light weight make it very convenient to use.
• The comparison of linear BEC and switch-mode BEC:When using a lithium battery pack more than 3S,a switch-mode BEC has much higher efficiency than linear BEC.
  For a traditional linear BEC,For example,a 4S lithium battery back has a typical voltage of 14.8V,in order to let BEC output 5V/1A,the current flow into the BEC is at least 1A,so the power on BEC is 14.8V*1A=14.8W.But the useful output power is only 5V*1A=5W,so the efficiency of the linear mode BEC is just 5W/14.8W=33.8%,the redundant power 14.8W-5W=9.8W changes to heat,which makes the BEC very hot.
  For a switch-mode BEC in the above case,in order to let BEC output 5V/1A, the current flow into BEC is only 0.38A(actual test data),so the power on BEC is 14.8*0.38A=5.6W,and the efficiency of BEC is 5W/5.6W=89.3%.
• Do not worry about the polarity of battery pack.If the polarity is not correct,the UBEC can not work,but it will not be destroyed.What you need to do is just swap the battery pack polarity.
• A shield covers almost all the electronic components on PCB,and a perrite ring is attached with the output wires to decrease the electromagnetic interference.  

Harga Rp. 90.000,-

EP-5030 5030R 5x3" 3-Blade CCW & CW

Material:Nylon
Body color:Black
Size: 5.0 x 3.0
Weight: about 2.4g/pcs
Center hole diameter: 3.0mm
Center Block thickness: 5.0mm
 
Configuration:
 
Forward Blade(5030) x 8pcs
Reverse Blade(5030R) x 8pcs
 
Diameter is 5mm hole,also have 3mm,3.17mm and 4mm adapter!

Harga Rp. 45.000 /pasang

3.17mm RC Aluminum Bullet Propeller Adapter

3.17mm RC Aluminum Bullet Propeller Adapter Holder for Brushless Motor Prop
Features:
Brand new.
High quality aluminum material.
Motor axle hole diameter: 3.17mm.
Suitable for brushless motors and speed controllers.
Delicate workmanship.
Specifications:
Color: Silver
Material: Aluminum
Motor Axle hole diameter: 3.17mm
Single item size: 2.4 * 1.2cm(L * D)
Single item weight: 4g

Harga Rp. 13.000,-

Motor A2212 1000KV

desc :
KV: 1000
Max Efficiency: 80%
Max Efficiency Current: 4-10A (>75%)
Current Capacity: 12A/60s
No Load Current @ 10V: 0.5A
No. Of Cells: 2-3 Li-Poly
Motor Dimensions: Φ27.5 x 30mm
Shaft Diameter: Φ3.17mm
Weight: 47g/set
Including: 1 set 2212 1000KV Brushless Outrunner Motor with Mounts *4

• Name : A(200200)608 - 4 x Brushless Motor A2212/13 KV1000.
• No load Current : 10 V : 0.5 A.
• Maximum current: 12A/60s.
• Apply to the ESC : 30A.
• Apply to the Lipo : 2 - 3S.
• Apply to the NiCD / NiMH : 6 - 9S.
• Apply to the Propeller : 8x4.5" 9x4.5" 10x4.5" 10x4.7".
• Apply to the three Propeller : 7x4.5" 8x4.5" 9x4.5".
• Does not contain Dimension : 28.0mm x 26.8mm .
• Does not contain Dimension : 28.0mm x 40.0mm .
• Shaft diameter : 3.175mm.
• Weight : 47g x 4.

Harga Rp. 150.000,-

Roda 20x8x1,9 mm

Diameter: 20mm
Thickness: 8mm
Aperture: 1.9mm

Harga Rp. 12.000,-

Roda Bebas

360 degrees in any direction

Height: 2.1cm

Width: 3.2cm

Length: 4.8cm

Mounting holes diameter: 0.4cm

Install pitch:40mm

Ball diameter: 16mm

Load limit: 18kg

 

Harga Rp. 35.000,- 

Motor DC 1,5-9 V

Strong magnetic carbon brush motor high speed horsepowerSize: 3.2 * 2 * 1.5cm
Shaft length: 7MM
Shaft Diameter: 2mm embossed shaftVoltage :1.5-9V
Weight: 30.02g
Current: 400MA
Speed: 6v speed 23,000 rpm

Harga Rp. 62.000

Roda 30x2 mm

Diameter:30mm
Shaft hole :2mm (Please choose 2mm axles)
Material: Plastic
Can be directly fixed on the dual axis small motor 

Harga Rp. 12.000,-

Arduino SD Card Module Slot Socket Reader ARM MCU

Description :
* 100% Brand new & high qualtiy
* Can be used for SD Card more easily, such as for MP3 Player, MCU/ARM system control.
* All SD SPI pins output, MOSI, SCK, MISO and CS.
* Support 5V/3.3V input
SD Card module can make your SD application more easier and simple.
It is easily interfaced as a peripheral to your arduino sensor shield module.
Through programming, you can read and write to the SD card using your arduino.

Size : Approx  52mm × 30mm × 12 mm

Harga Rp. 25.000,-

MQ-2 Smoke liquefied flammable gas sensor module methane gas

Harga Rp. 30.000,-

ESP-12E (replace ESP-12) ESP8266 remote serial Port WIFI wireless module

Harga Rp. 70.000,-

Metal gear Digital MG90S 9g Servo

Products Description:

• For: RC Helicopter Plane Boat Car
• Weight : 13.4G
• Dimension : 22.8mm x 12.2mm x 28.5mm
• Stall Torque : 1.8kg/cm(4.8V )2.2kg/cm(6V)
  Temperature Range : 0 degree to 55 degree
• Operating Speed : 0.1sec/60degree(4.8v),
• 0.08sec/60degree(6v)
• Dead Band Width : 5 usec
• Operation Voltage : 4.8 - 6Volts
• Motor Type : coreless motor
• Gear Type : All Metal gear
• Connector Wire Length : 175mm

Harga Rp. 60.000,-

HC-05 master-slave 6pin Bluetooth Module

HC05 JY-MCU anti-reverse, integrated Bluetooth serial pass-through module, HC-05 master-slave 6pin

Harga Rp. 80.000,-

SG90 9g Mini Micro Servo

Product Description

Steering gear definition of three lines:

Dark gray: GND

Red: VCC 4.8-7.2V

Orange line: pulse input

 

 

 

Model: SG90

Technical data given by the manufacturers:
Size: 21.5mmX11.8mmX22.7mm
Weight: 9 grams
No-load speed: 0.12 seconds / 60 degrees (4.8V)
Stall torque of 1.2 - 1.4 kg / cm (4.8V)
Operating temperature: -30 to +60 degrees Celsius
Dead-set: 7 microseconds
Operating voltage: 4.8V-6V

Harga Rp. 40.000,-