Wednesday, December 18, 2013

Universal GPS Aluminum Folding Mount

Harga Rp. 110.000,-

Wednesday, December 11, 2013

FrSky Delta 8 2.4Ghz 8CH Multi-Brand Receiver D8/V8 Futaba S-FHSS/FHSS Hitec AFHSS Compatible

The FrSky Delta 8 receiver is a multi-brand 2.4GHz receiver that is compatible with FrSky D8/V8, Futaba S-FHSS/FHSS and Hitec A-FHSS. It also features CPPM and RSSI outputs.

This unit works with the following systems:
FrSky D8
FrSky V8
Futaba S-FHSS
Futaba FHSS
Hitec 2.4GHz A-FHSS

Plus you can put the receiver into PPM and RSSI output mode for flybarless helicopters, multi-copter and FPV users.

When binding, the Delta 8 will search and find which system is active and then bind to that transmitter - all automatically. Alternatively you can use a set of jumpers to force the receiver to only look for a particular brand.

Receiver Specifications:
Operating Voltage Range: 3.0V-16V (HV Version)
Operating Current: 30mA
Specified Range: 1.5km-2.5km
Resolution: 3072
Latency: 22ms
Number of Channels: 8CH
Dimensions: 49mm×24.5mm×15mm
Weight: 9.3g

Harga Rp. 375.000,-

FrSky D8R-XP 2.4Ghz Receiver (w/telemetry)

FrSky D8R-XP 2.4Ghz Receiver (w/telemetry)

Compatibility:

Compatible with FrSky two way telemetry modules: DFT, DJT, DHT, DHT-U

Specification:
Dimension: 55*25*14mm
Weight: 12.4g
Operating Voltage Range: 3.5V-10.0V
Operating Current: 100mA
Operating Range: 1.5km
Resolution: 3072 (>11bit)

Harga Rp. 400.000,-

Friday, November 22, 2013

Tiny Pan Tilt FPV Camera Gimbal

Tiny Pan Tilt FPV Camera Gimbal
Made by nylon, low cost & light. Use this with 2 x 9G servos for pan and tilt.

Fits with mini cameras which are smaller than 30 x 30 side holder should be removed for installation

Harga Rp. 100.000,-

Tiny Pan Tilt FPV Camera Gimbal

Made by nylon, low cost & light. Use this with 2 x 9G servos for pan and tilt.

Fits with mini cameras which are smaller than 30 x 30 side holder should be removed for installation

- See more at: http://kamkits.com/index.php?route=product/product&product_id=343#prettyPhoto

Tiny Pan Tilt FPV Camera Gimbal

Made by nylon, low cost & light. Use this with 2 x 9G servos for pan and tilt.

Fits with mini cameras which are smaller than 30 x 30 side holder should be removed for installation

- See more at: http://kamkits.com/index.php?route=product/product&product_id=343#prettyPhoto

Wednesday, November 20, 2013

15W Broadband FM Transmitter

15W Broadband FM Transmitter kit with 20x4 LCD Designed for FM broadcast transmitters High quality PLL chip MC145170 Frequency 87.5-108MHz (76-108MHz on request*) Larger display using 20x4 LCD DC 12-15 Volts Low harmonics mosfet oscillator PD55015 RF Power MOSFET adjustable 0 to 15 Watts from panel menus No Tune / Broadband design 50kHz PLL Steps Digital power meter (forward/reflected), voltage, current, and temperature RF output ruggedness: SWR protection (adjustable from menus) Polarity protection, temp protection RF-OFF while not locked to protect the amplifier Output Impedance 50 Ohms Quartz Locked PLL Frequency Control Low Pass Filter included Output connector: solder posts (no connector on board) Audio connectors: RCA jack No Expensive Test Equipment Required SMD components High quality PCB Main PC Board Size : 164 x 96mm Controller PC Board Size : 138 x 64mm Easy to use

Harga Rp. 1.000.000,-

Friday, November 15, 2013

ArduFlyer/APM 2.5.x u-Blox CN06 Plus GPS Receiver

ArduFlyer/APM 2.5.x u-blox CN06 Plus GPS Receiver

ArduFlyer/APM 2.5.x External Magnetometer

ArduFlyer/APM 2.5.x Status LEDs

**********************************************

APM 2.5 Hardware ArduPilot Firmware Rctimer ArduFlyer Tutorials & Discussion:

http://www.rcgroups.com/forums/showthread.php?t=2021896

**********************************************

Features and Specifications:

GPS
u-blox UBX-G6010-ST
5 Hz update rate
25 x 25 x 2 mm ceramic patch antenna
LNA and SAW filter
Rechargeable 3V lithium backup battery
Low noise 3.3V regulator
I2C EEPROM for configuration storage
GPS Power and Fix indicator LED
40.64 x 66.42 x 7.8 mm total size, 12.4 grams
Mounting hole diameter: 3.3mm
Mounting hole installation position 61.09 x 35.31mm

Magnetometer
HMC5883L Magnetometer
ArduFlyer/APM 2.5.x compatible external Magnetometer I2C 3.3V interface
ArduFlyer/APM 2.5.x compatible Status LEDs for ARM and GPS

Package Content
CN06 Plus PCB
Cable 100mm ArduFlyer/APM 2.5.x compatible GPS 5-pin JST
Cable 100mm ArduFlyer/APM 2.5.x compatible I2C 4 pin JST
Cable 100mm ArduFlyer/APM 2.5.x compatible Status LED 0.1

Harga Rp. 500.000,-

MULTIWII AIOP V2.0 ALL IN ONE PRO Flight Controller

Video:

http://www.youtube.com/watch?v=Emf7WAa0YcY&sns=em

http://vimeo.com/47677259

http://www.youtube.com/watch?v=OkkoudNBIQc

Hardware Features:
         - Supported MegaPirateNG /ArduCopterNG/ArduPlaneNG/MultiWii firmware
         - 8-axis motor output and 3 servos output for gimbal system
         - 8 input channels for standard receiver and PPM SUM input channel
         - 4 serial ports for debug/Bluetooth/OSD/GPS/telemetry module
         - 8 Analog port for Airspeed Sensor/Current & Voltage Sensor/LED controller
         - User-defined pads D32~37 & PG1~PG5
         - I2C 5V port for external device
         - Output/USB ports provided over current protection
         - Reverse polarity protection for input power
         - Select jumper for choose internal or external magnetometer
         - Onboard 16Mbit Dataflash chip for automatic datalogging
         - ATMega 2560-16AU Microcontroller
         - MPU6050 6-axis gyro/accel with Motion Processing Unit
         - HMC5883L 3-axis digital magnetometer
         - MS5611-01BA03 highprecision altimeter with metal cap
         - FT232RQ USB-UART chip and Micro USB receptacle for uploading firmware and debug
         - PCA9306DP1 logic level converter for I2C
         - Match the standard of RoHS

Input power selection
         - One of the following way
         - Connect 5V power cable from ESC or UBEC to ESC/Servo port, the J1 jumper must be closed.
         - Connect 5V power cable to the external power port, the J1 jumper must be removed.

Other
         ·Dimension: 50mmX50mmX11.6mm
         ·Weight: 14.5g
         ·Fixing hole spacing: 45mm
         ·Hole diameter: 3.1mm

Package content
         ·ALL IN ONE PRO Flight Controller x 1
         ·3Pin to 1Pinx3 cable 100mm x 3
         ·3Pin to 3Pin cable 100mm x 1
         ·Molex 1.25mm 4Pin cable 100mm x1
         ·Molex 1.25mm 6Pin cable 100mm x1
         ·Molex 1.25mm 8Pin cable 100mm x2

Reference material

http://www.rctimer.com/download/Crius_AIOP_Manual_MWC.pdf

Harga Rp. 800.000,-

APM 2.6 Set (external compass)

The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

APM 2.6 requires a GPS unit with an onboard compass for full autonomy.

If you are using APM 2.6 with a GPS module that does not have a compass sensor, you must use a stand-alone external compass. We recommend this one with this cable.

Features:
- Arduino Compatible!
- Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally
- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
- Onboard 4 MegaByte Dataflash chip for automatic datalogging
- Optional off-board GPS, uBlox LEA-6H module with Compass.
- One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

Resources:
- ArduPlane manual
- ArduCopter manual
- ArduRover manual

Datasheets:
- MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking.
- HMC5883L-TR, 3-Axis Digital Compass.
- MS5611, MEAS High Resolution Altimeter.

Documentation:
- Installing GPS: Plane, Copter, Rover
- Dimensional drawing
- EAGLE files
- User Guide PDF

Harga Rp. 2.800.000,-

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

APM 2.6 requires a GPS unit with an onboard compass for full autonomy.

If you are using APM 2.6 with a GPS module that does not have a compass sensor, you must use a stand-alone external compass. We recommend this one with this cable.

Features:

- Arduino Compatible!

- Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally

- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer

- Onboard 4 MegaByte Dataflash chip for automatic datalogging

- Optional off-board GPS, uBlox LEA-6H module with Compass.

- One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.

- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.

- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

Resources:

- ArduPlane manual

- ArduCopter manual

- ArduRover manual

Datasheets:

- MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking.

- HMC5883L-TR, 3-Axis Digital Compass.

- MS5611, MEAS High Resolution Altimeter.

Documentation:

- Installing GPS: Plane, Copter, Rover

- Dimensional drawing

- EAGLE files

- User Guide PDF

- See more at: http://kamkits.com/index.php?route=product/product&product_id=62#sthash.z2wRC0zE.dpuf

Sunday, September 15, 2013

4.0mm Brushless Motor Adapter

Harga Rp. 45.000

Friday, August 30, 2013

VGA OV7670 CMOS Camera Module Lens CMOS 640X480 SCCB Compatible W/ I2C Interface

Brand new and high quality.
High sensitivity for low-light operation.
Low operating voltage for embedded application.
Standard SCCB interface compatible with I2C interface.
Raw RGB, RGB (GRB4:2:2, RGB565/555/444),YUV(4:2:2) and YCbCr(4:2:2)output format.
Support VGA, CIF and from CIF to 40 x 30 format.
Vario Pixel method for sub-sampling.
Auto Image Control: AEC, AGC, AWB, ABF, ABLC.
Image Quality Control: Color saturation, hue, gamma, sharpness and anti-blooming.
ISP includes noise reduction and defect correction.
Support image scaling.
Lens shading correction.
Flicker 50/60Hz auto detection.
Color saturation level auto adjust.
Edge enhancement level auto adjust.
De-noise level auto adjust.

Parameter:

Photosensitive Array: 640 x 480.

IO Voltage: 2.5V to 3.0V.

Operating Power: 60mW/15fpsVGAYUV.

Sleeping Mode: <20μA.

Operating Temperature: -30 to 70 deg C.

Output Format: YUV/YCbCr4:2:2 RGB565/555/444 GRB4:2:2 Raw RGB Data (8 digit).

Lens Size: 1/6".

Vision Angle: 25 degree.

Max. Frame Rate: 30fps VGA.

Sensitivity: 1.3V / (Lux-sec).

Signal to Noise Ratio: 46 dB.

DynamicRange: 52 dB.

Browse Mode: By row.

Electronic Exposure: 1 to 510 row.

Pixel Coverage: 3.6μm x 3.6μm.

Duck Current: 12 mV/s at 60℃.

PCB Size (L x W): Approx. 1.4 x 1.4 inch / 3.5 x 3.5 cm.

Harga Rp, 120,000,-

Tuesday, August 13, 2013

Selamat Idul Fitri

KF-TRONIK
Assalamu'laikum Wr Wb
Taqaballahu Minna Wa Minkum
Mohon Maaf Atas Layanan Kamis Selama ini yang kurang
Berkenan atau kurang Memuaskan
Semoga Kedepan kami menjadi Lebih baik lagi

Wassalam

Koko Joni

Saturday, July 13, 2013

IR Pyroelectric Infrared IR PIR Motion Sensor Detector Module HC- SR501

Color: White + Green
Dimension: 3.2cm x 2.4cm x 1.8cm (approx)
Infrared sensor with control circuit board
The sensitivity and holding time can be adjusted
Working Voltage Range: DC 4.5V- 20V
Current drain:<60uA
Voltage Output: High/Low level signal:3.3V TTL output
Detection distance: 3--7M(can be adjusted)
Detection range: <140°
Delay time: 5-200S(can be adjusted, default 5s +-3%)
Blockade time: 2.5 S (default)
Trigger: L: Non-repeatable trigger H: Repeat Trigger (default)
Work temperature:-20-+80°C
Trigger Method: L unrepeatable trigger / H repeatable trigger
contoh penggunaan bisa dilihat di link berikut:
Dokumentasi

Harga Rp 50.000

Tuesday, June 18, 2013

Combiners 3 ways FM Power Divider

3 ways FM Power Combiner FM Band 87.5-108MHz Input up to 50 watt max. (replace resistor for increase power handling max.) Input/Output 50 ohm SMD resistor High quality PCB

Harga Rp. 125.000,-

Combiner 2 ways FM Power Divider

2 ways FM Power Divider FM Band 87.5-108MHz Input up to 50 watt max. (replace resistor for increase power handling max.) Input/Output 50 ohm SMD resistor High quality PCB

Harga Rp. 100.000,-

Combiner 1kW FM Directional Coupler

Directional Coupler 1000W Frequency range 86-110 MHz Input/output 50 ohm Power rating up to 1000 watt Double side high quality PCB FREE 1kW DC COUPLER FOR PURCHASE FM PALLET

Harga Rp. 100.000,-

FM PALLETS AMPLIFIER

1000W FM pallet 87.5-108MHz, 43 - 48Volts Input/Output 50 ohms Pout 1000W with 3W input. 25dB gain minimum. Low distortion Class B push-pull. Small size: only 2.25 in x 4.0 inches 78% efficiency typical. Power requirements 22 to 24 ADC 800W out at 43V. Power requirements 25 to 27 ADC 1000W out at 50V

Harga Rp. 5.500.000,-

Thursday, May 16, 2013

Quadcopter Power Distribution Board

Designed in house by the HobbyKing Enginerds, this handy power distribution board has the same foot print as our Multri-rotor control boards and is the ultimate solution for tidy power distribution wiring. Simply use 3.5mm male connectors on your ESCs and plug a battery in. The PCB is Gold plated for optimality efficiency and also features a bling port (aka 2 pin JST size auxiliary power out) Perfect for powering LEDs or any accessory fitted to your Quadcopter.

Features:

Current: 4 x 20A Outputs (MAX)

Power Input: XT60 with 12AWG wire

Motor output: 4 x 3.5mm Female bullet plug

Aux output: 2 pin JST compatible

Harga 85.000,-

Wednesday, May 8, 2013

RCTIMER 2-Axis Brushless Gimbal Controller & IMU v1.0

The gimbal supported 2-Axis brushless motors and is adjustable, so it can be balanced perfectly.

Brushless Gimbal Controller by Ludwig FÃ¤rber (Hardware and Software) , Alexander Rehfeldt (Software) and Christian Winkler (Software)

This is an OPEN SOURCE Project.

Hardware Features:

- ATMega328P microcontroller

- Onboard FT232RL for debug

- 2~6 cells lipo input

- 3 Channels input

- Multiport

-·UART Port

- MPU6050 6 axis gyro/accel with Motion Processing Unit

- On board logic level converter

Other

- Dimension: 50mmx50mm

- Weight: 25g(include IMU board)

Package content

- Brushless Gimbal Controller x 1

- IMU board x1

- 5Pin cable 300mm x1

FT232RL drivers

http://www.ftdichip.com/Drivers/VCP.htm

Schmatics, Firmware and GUI tool

http://code.google.com/p/brushless-gimbal/downloads/list

Harga Rp. 775.000,-

Turnigy 4X FHSS 2.4ghz Transmitter and Reciever (Mode 1)

The Turnigy 4X is a great entry level 2.4ghz Transmitter and reciever that uses solid and reliable FHSS spread spectrum technology. The Turnigy 4X has both a nice quality look and feel, especially given it's low price, features include servo reversing, trims and Delta Mixing.

Turnigy 4X Transmitter Specs:

Resolution: 4096Frequency: 2.4ghz ISM Frequency RangeModulation: GFSKSpread Spectrum Mode: FHSSNumber of Frequency Channels: 20Hopping Rate: 240 jump/sOutput Power: <=20dbmWorking Current: <=150mAWorking Voltage: 1.2v x 4 (AA/Nimh)Dimensions: 200mm x 185mm x 105mm

Net Weight: 474g

Turnigy XR500 Reciever Specs:Channel: 5 (inc RX Battery Input)

Frequency: 2.4g ISM Frequency Range

Power: 4.5v ~ 5.5v/<30ma

Net Weight: 11g

Dimensions: 41mm x 28mm x 14mm

Requires:

4 x AA Type Battery For Operation

Harga RP. 425.000,-

Turnigy 6X FHSS 2.4ghz Transmitter and Reciever (Mode 2)

The Turnigy 6X is a great entry level 2.4ghz Transmitter and reciever that uses solid and reliable FHSS spread spectrum technology. The Turnigy 6X has both a nice quality look and feel, especially given it's low price, features include Retract & Flap switches, servo reversing, trims, charging port and Delta Mixing.

Turnigy 6X Transmitter Specs:

Resolution: 1024

Frequency: 2.4ghz ISM Frequency Range

Modulation: GFSK

Spread Spectrum Mode: FHSS

Number of Frequency Channels: 20

Hopping Rate: 125 jump/s

Output Power: <=20dbm

Working Current: <=150mA

Working Voltage: 1.2v x 4 (AA/Nimh)

Dimensions: 200mm x 185mm x 105mm

Turnigy XR700 Reciever Specs:

Channel: 7 (inc RX Battery Input)

Frequency: 2.4g ISM Frequency Range

Power: 4.5v ~ 9.6v/<30ma

Net Weight: 11.5g

Dimensions: 41mm x 28mm x 14mm

Requires:

4 x AA Type Battery For Operation

Harga Rp. 525.000,-

Turnigy 9X 9Ch Transmitter w/ Module & 8ch Receiver (Mode 2) (v2 Firmware)

With v2 firmware update, correcting many flaws of the previous 9X, plus inbuilt 2.4Ghz (no daggy second antenna) this is a quality, reliable 2.4Ghz system suitable for beginners and pro pilots alike.

Get that locked-in feeling that only 2.4Ghz glitch free technology can provide.

Ultra fast reaction times and interference free control of your model is only achievable with this 2.4Ghz technology.

Without a doubt, the best value 9Ch system available!

Number of Channnel: 8ch ppm/9ch pcm

Display: 128*64LCD

Support Type: Heli/Acro/Glid

Support user: 8

Stick model: 4

Encoder type: ppm/pcm

Subtrim: Yes

Number of Channnel: 8ch ppm/9ch pcm

Display: 128*64LCD

Support Type: Heli/Acro/Glid

Support user: 8

Stick model: 4

Encoder type: ppm/pcm

Subtrim: Yes

Simulator Interface: Yes

Buzzer: Yes

Low Voltage Show: Yes

Required:

Battery

Included:

Turnigy 9x 9Ch Transmitter

Turnigy RF9X-V2 module

Turnigy 9X8C-V2 8-channel receiver

Important.

The TURNIGY 9X has been reflashed with the new v2 firmware, fixing previous menu and mixing issues. This firmware flash is only available from our TURNIGY 9X system as we flash each unit in our office before it is shipped.

Purchases of any other rebranded version of the TURNIGY 9X will not have the latest firmware and patches (even the OEM factory does not have these updates).

NOTE: "SWITCH ERROR" means you have one of the switches in the wrong position when you turn the radio on. It is not a fault.

Simulator Interface: Yes

Buzzer: Yes

Low Voltage Show: Yes

Harga Rp. 900.000,-

Thursday, April 4, 2013

ATMEGA16A-PU ATMEGA16A DIP-40 NEW GOOD QUALITY

harga Rp. 37.000,-

Turnigy 2S 3S Balance Charger. Direct 110/240v Input

Extremely easy to use and reliable.The TGY-3 Balance charger from Turnigy makes charging 2 or 3S lipos from your 110v or 240v mains power supply a simple task!

China is flooded with cheap chargers made from unknown manufacturers, giving inconsistent results. Rest assured this product is reliable, includes warranty and comes with the correct documentation.

Specification:

Input: 110v or 240v A/C (50/60Hz)

Output: 650mA per cell CE, FCC Certified.

Harga : Rp. 175.000

Turnigy balancer & Charger 2S-3S

Spesification:
Turnigy balancer & Charger 2S-3S
Fits all Zippy 3S or 2S packs and charges at a rate of around 800mAh.
This is an excellent & cheap solution to charging 2 or 3S lipoly. Connect 4-5 chargers at once and charge multiple packs from the same power source!
Input: 12~15v DC

Harga : Rp. 75.000

1x40 Pin 2.54 mm Single Row Female Pin Header

1x40 Pin 2.54 mm Single Row Female Pin Header

Harga Rp. 2.500,-

Mini Solderless Prototype Breadboard 170 Tie-points for Arduino Shield New

Description

100% brand new and high quality

Material: ABS

Mini Solderless Breadboard

1 Terminal Strip

Tie-point 170

Completely reusable

Coloured coordinates for easy component placement

Phosphor bronze nickel plated spring clips

Accepts a variety of wire sizes (29-20 AWG)

Dimensions: 44x33x9.0mm

Color : Red, Black. White, Blue, Green

Harga Rp. 18.000,-

NRF24L01+ 2.4GHz Wireless Transceiver Module For Arduino Microcontroller

Deskripsi

1. Maximum operating speeds up to 2Mbps, GFSK modulation efficiency, Anti-interference ability, Particularly suitable for industrial control applications.
2.125 Channels, Multi-point communication and frequency hopping to meet the communication needs
3.Built-in hardware CRC error detection, Multipoint communication address control.
4.Low-power 1.9 ~ 3.6V, only 1uA on Power down mode
5.Built-in 2.4Ghz antenna
6.Available software to set the address, only received local Address when output data(Provide interrupt instruction), can be directly connected to a variety of microcontrollers, Software programming is very convenient.
7.Built-in voltage regulator
8.Standard DIP Pitch Interface for embedded applications
9.size: 34mm X 17mm X 1mm

Harga satu pasang (2 biji) Rp. 60.000,-

Monday, March 11, 2013

RCTimer ArduFlyer Kit V2.5

The ArduFlyer is a complete open source autopilot system. Its design come from 3DRobotics and it 100% compatible with APM2.5. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. This version comes with the RC/Servo connectors unsoldered, so you can choose between straight or right-angled ones, both of which are included.