Tiny Pan Tilt FPV Camera Gimbal

Tiny Pan Tilt FPV Camera Gimbal
Made by nylon, low cost & light.  Use this with 2 x 9G servos for pan and tilt.

Fits with mini cameras which are smaller than 30 x 30 side holder should be removed for installation

Harga Rp. 100.000,-

Tiny Pan Tilt FPV Camera Gimbal

Made by nylon, low cost & light.  Use this with 2 x 9G servos for pan and tilt.

 

Fits with mini cameras which are smaller than 30 x 30 side holder should be removed for installation

- See more at: http://kamkits.com/index.php?route=product/product&product_id=343#prettyPhoto

Tiny Pan Tilt FPV Camera Gimbal

Made by nylon, low cost & light.  Use this with 2 x 9G servos for pan and tilt.

 

Fits with mini cameras which are smaller than 30 x 30 side holder should be removed for installation

- See more at: http://kamkits.com/index.php?route=product/product&product_id=343#prettyPhoto

15W Broadband FM Transmitter

15W Broadband FM Transmitter kit with 20x4 LCD Designed for FM broadcast transmitters High quality PLL chip MC145170 Frequency 87.5-108MHz (76-108MHz on request*) Larger display using 20x4 LCD DC 12-15 Volts Low harmonics mosfet oscillator PD55015 RF Power MOSFET adjustable 0 to 15 Watts from panel menus No Tune / Broadband design 50kHz PLL Steps Digital power meter (forward/reflected), voltage, current, and temperature RF output ruggedness: SWR protection (adjustable from menus) Polarity protection, temp protection RF-OFF while not locked to protect the amplifier Output Impedance 50 Ohms Quartz Locked PLL Frequency Control Low Pass Filter included Output connector: solder posts (no connector on board) Audio connectors: RCA jack No Expensive Test Equipment Required SMD components High quality PCB Main PC Board Size : 164 x 96mm Controller PC Board Size : 138 x 64mm Easy to use

 

Harga Rp. 1.000.000,-

ArduFlyer/APM 2.5.x u-Blox CN06 Plus GPS Receiver

ArduFlyer/APM 2.5.x u-blox CN06 Plus GPS Receiver

ArduFlyer/APM 2.5.x External Magnetometer

ArduFlyer/APM 2.5.x Status LEDs

**********************************************

APM 2.5 Hardware ArduPilot Firmware Rctimer ArduFlyer Tutorials & Discussion:

http://www.rcgroups.com/forums/showthread.php?t=2021896

**********************************************

Features and Specifications:

GPS
u-blox UBX-G6010-ST
5 Hz update rate
25 x 25 x 2 mm ceramic patch antenna
LNA and SAW filter
Rechargeable 3V lithium backup battery
Low noise 3.3V regulator
I2C EEPROM for configuration storage
GPS Power and Fix indicator LED
40.64 x 66.42 x 7.8 mm total size, 12.4 grams
Mounting hole diameter: 3.3mm
Mounting hole installation position 61.09 x 35.31mm

Magnetometer
HMC5883L Magnetometer
ArduFlyer/APM 2.5.x compatible external Magnetometer I2C 3.3V interface
ArduFlyer/APM 2.5.x compatible Status LEDs for ARM and GPS

Package Content
CN06 Plus PCB
Cable 100mm ArduFlyer/APM 2.5.x compatible GPS 5-pin JST
Cable 100mm ArduFlyer/APM 2.5.x compatible I2C 4 pin JST
Cable 100mm ArduFlyer/APM 2.5.x compatible Status LED 0.1



Harga Rp. 500.000,-

MULTIWII AIOP V2.0 ALL IN ONE PRO Flight Controller

Video:

http://www.youtube.com/watch?v=Emf7WAa0YcY&sns=em

http://vimeo.com/47677259

http://www.youtube.com/watch?v=OkkoudNBIQc

Hardware Features:
         - Supported MegaPirateNG /ArduCopterNG/ArduPlaneNG/MultiWii firmware
         - 8-axis motor output and 3 servos output for gimbal system
         - 8 input channels for standard receiver and PPM SUM input channel
         - 4 serial ports for debug/Bluetooth/OSD/GPS/telemetry module
         - 8 Analog port for Airspeed Sensor/Current & Voltage Sensor/LED controller
         - User-defined pads D32~37 & PG1~PG5
         - I2C 5V port for external device
         - Output/USB ports provided over current protection
         - Reverse polarity protection for input power
         - Select jumper for choose internal or external magnetometer
         - Onboard 16Mbit Dataflash chip for automatic datalogging
         - ATMega 2560-16AU Microcontroller
         - MPU6050 6-axis gyro/accel with Motion Processing Unit
         - HMC5883L 3-axis digital magnetometer
         - MS5611-01BA03 highprecision altimeter with metal cap
         - FT232RQ USB-UART chip and Micro USB receptacle for uploading firmware and debug
         - PCA9306DP1 logic level converter for I2C
         - Match the standard of RoHS     

Input power selection
         - One of the following way
         - Connect 5V power cable from ESC or UBEC to ESC/Servo port, the J1 jumper must be closed.
         - Connect 5V power cable to the external power port, the J1 jumper must be removed.

Other
         ·Dimension: 50mmX50mmX11.6mm
         ·Weight: 14.5g
         ·Fixing hole spacing: 45mm
         ·Hole diameter: 3.1mm

Package content
         ·ALL IN ONE PRO Flight Controller x 1
         ·3Pin to 1Pinx3 cable 100mm x 3
         ·3Pin to 3Pin cable 100mm x 1
         ·Molex 1.25mm 4Pin cable 100mm x1
         ·Molex 1.25mm 6Pin cable 100mm x1
         ·Molex 1.25mm 8Pin cable 100mm x2

Reference material

http://www.rctimer.com/download/Crius_AIOP_Manual_MWC.pdf

Harga Rp. 800.000,-

APM 2.6 Set (external compass)

The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

APM 2.6 requires a GPS unit with an onboard compass for full autonomy.

If you are using APM 2.6 with a GPS module that does not have a compass sensor, you must use a stand-alone external compass. We recommend this one with this cable.

Features:
- Arduino Compatible!
- Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally
- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
- Onboard 4 MegaByte Dataflash chip for automatic datalogging
- Optional off-board GPS, uBlox LEA-6H module with Compass.
- One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

Resources:
- ArduPlane manual
- ArduCopter manual
- ArduRover manual

Datasheets:
- MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking.
- HMC5883L-TR, 3-Axis Digital Compass.
- MS5611, MEAS High Resolution Altimeter.

Documentation:
- Installing GPS: Plane, Copter, Rover
- Dimensional drawing
- EAGLE files
- User Guide PDF


Harga Rp. 2.800.000,-

The APM 2.6 is a complete open source autopilot system and the bestselling technology that won the prestigious 2012 Outback Challenge UAV competition. It allows the user to turn any fixed, rotary wing or multirotor vehicle (even cars and boats) into a fully autonomous vehicle; capable of performing programmed GPS missions with waypoints. Available with top or side connectors.

 

This revision of the board has no onboard compass, which is designed for vehicles (especially multicopters and rovers) where the compass should be placed as far from power and motor sources as possible to avoid magnetic interference. (On fixed wing aircraft it's often easier to mount APM far enough away from the motors and ESCs to avoid magnetic interference, so this is not as critical, but APM 2.6 gives more flexibility in that positioning and is a good choice for them, too). This is designed to be used with the 3DR uBlox GPS with Compass (see option below), so that the GPS/Compass unit can be mounted further from noise sources than APM itself.

 

APM 2.6 requires a GPS unit with an onboard compass for full autonomy.

 

If you are using APM 2.6 with a GPS module that does not have a compass sensor, you must use a stand-alone external compass. We recommend this one with this cable.

 

Features:

- Arduino Compatible!

- Can be ordered with top entry pins for attaching connectors vertically, or as side entry pins to slide your connectors in to either end horizontally

- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer

- Onboard 4 MegaByte Dataflash chip for automatic datalogging

- Optional off-board GPS, uBlox LEA-6H module with Compass.

- One of the first open source autopilot systems to use Invensense's 6 DoF Accelerometer/Gyro MPU-6000.

- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.

- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and usb functions respectively.

 

Resources:

- ArduPlane manual

- ArduCopter manual

- ArduRover manual

 

Datasheets:

- MPU-6000, Six-Axis (Gyro + Accelerometer) MEMS MotionTracking.

- HMC5883L-TR, 3-Axis Digital Compass.

- MS5611, MEAS High Resolution Altimeter.

 

Documentation:

- Installing GPS: Plane, Copter, Rover

- Dimensional drawing

- EAGLE files

- User Guide PDF

- See more at: http://kamkits.com/index.php?route=product/product&product_id=62#sthash.z2wRC0zE.dpuf